Platon In-Line Pitot
Can we help?
- Flow sensors for liquids or gases
- ±1% of actual flow rate
- Full electron beam welded construction
- Flow averaging
- Internal isolation ball valve
- No power supply required
Full Product Specification
| Material: | Stainless Steel |
| Repeatability: | ±0.1% (typical) |
| Output: | DP (proportional to the square of fluid velocity) |
| Temperature: | -20ºC to 225ºC insertion model |
| Range: | 0.7 to 250 m³/hr (air @ ATP), 0.1 to 65 m³/hr (water @ 20ºC) |
| Tappings: | ¼" BSP |
| Pipe Connection: | Threaded NPT Male |
| Pressure: | 30 bar max |
| Pipe Size | ½" to 2" nominal bore Sch 80 |
Recommended Products
DP & Flow Transmitter
MICRO-BAR DIFFERENTIAL PRESSURE/FLOW TRANSMITTER
Micro-Bar electronic transmitter incorporates a capacitance based differential pressure cell for sensitive measurement on Air or other dry gases. Designed for gas flow measurement applications on extraction or ventilation systems, the micro based electronics uses calibration formulae required for Flo- Bar Averaging Pitot tubes, Orifice Plates or other standard DP based sensors. Simply installed adjacent to the flow line, standard pressure impulse tubing links the sensor directly to the Micro-Bar unit. Flow rate, flow units and alarm status are displayed on the two line LCD: external signal transmission is via the 4-20mA loop power,with separate alarm relay and totaliser pulse.
With simple adjustment over a 5:1 full scale pressure range available to the operator on site, the Micro-Bar suits varying process conditions or output scaling requirements. The micro based electronics simplifies site setup procedures, allowing adjustment of alarm output set points, totalisation pulse rate, averaging time and zero checking.
Micro-Bar is applicable to measuring pressure differentials on operating theatres, clean rooms or glove boxes, to monitor system performance and provide alarms. On process monitoring, Micro-Bar is used for air filter blockage monitoring and burner control on furnaces. For these duties, the display shows the pressure drop directly.
FEATURES
Platon Averaging Pitot Tube: Flo-Bar
The Flo-Bar is an Averaging Pitot Tube flow sensor for use on pipes/ducts or chimneys. Differential pressure created across the Flo-Bar has the standard square root relationship to flow rate, making a simple, removable sensor for installation or retrofit on flowlines of any size.
The unique design of the Flo-Bar profile provides a high accuracy, wide rangeability sensor: the standard integral manifold allows simple process isolation and easy installation of a DP measurement cell.
T-Bar Valves
A range of fine control valves, suitable for control of high pressure flow lines up to 6,000 psi. The non-rotating, self centreing, anti-galling spindle tip gives positive bubble tight shut-off, plus good flow control.
UKAS and Traceable Calibration
Roxspur Measurement & Control Ltd is an ISO 9001:2008 company, we offer UKAS and traceable calibration under BS/EN ISO17025 accredited procedures. Our certificate generation systems are purposely geared to meet the strict and specific requirement of the Aerospace industry.
Calibration
Based at our factory in Sheffield our accredited laboratories are available to provide either on-site or in-house calibration to either UKAS or national standards. We cover Temperature (up to 2,200ºC), Pressure (up to 1,200 bar), Flow (up to 2,500 L/min) and Electrical parameters and provide certification using the latest technology.
Our team of experienced on-site engineers hold accreditation for the on-site calibration of equipment including autoclaves, furnaces, thermocouples and probes, scales and balances, ovens and chambers, indicators and controllers, pressure and electrical. We cover the full spectrum of industry sectors. All calibration standards used meet the requirements of Table 3 of AMS 2750D, whether in the laboratory or on site, ensuring full compliance with the specification. To find out more about our on-site services please click here.
We supply thermocouples calibrated and certified to meet the requirements of Table 1 of AMS 2750D appropriate to customer specified usage.
Aerospace Heat Treatment Specialists
From the supply of a single thermocouple to fully managed service contracts, by working in partnership with our customers we can assist in obtaining and maintaining NADCAP approval. To find out more about our specialist aerospace services please click here.
Certification
Certificates generated are designed to meet the requirements of AMS 2750D with the option of UKAS certificates for added peace of mind.
DP & Flow Transmitter
MICRO-BAR DIFFERENTIAL PRESSURE/FLOW TRANSMITTERMicro-Bar electronic transmitter incorporates a capacitance based differential pressure cell for sensitive measurement on Air or other dry gases. Designed for gas flow measurement applications on extraction or ventilation systems, the micro based electronics uses calibration formulae required for Flo- Bar Averaging Pitot tubes, Orifice Plates or other standard DP based sensors. Simply installed adjacent to the flow line, standard pressure impulse tubing links the sensor directly to the Micro-Bar unit. Flow rate, flow units and alarm status are displayed on the two line LCD: external signal transmission is via the 4-20mA loop power,with separate alarm relay and totaliser pulse.
With simple adjustment over a 5:1 full scale pressure range available to the operator on site, the Micro-Bar suits varying process conditions or output scaling requirements. The micro based electronics simplifies site setup procedures, allowing adjustment of alarm output set points, totalisation pulse rate, averaging time and zero checking.
Micro-Bar is applicable to measuring pressure differentials on operating theatres, clean rooms or glove boxes, to monitor system performance and provide alarms. On process monitoring, Micro-Bar is used for air filter blockage monitoring and burner control on furnaces. For these duties, the display shows the pressure drop directly.
FEATURES
- DP measurement for gases
- High sensitivity and linearisation for Pitot tube flow measurement
- Digital flowrate display in Engineering units
- ±0.5% accuracy
- Flow totaliser pulse output
- High and low flow alarms
- Site programmable outputs
Platon Averaging Pitot Tube: Flo-Bar
The Flo-Bar is an Averaging Pitot Tube flow sensor for use on pipes/ducts or chimneys. Differential pressure created across the Flo-Bar has the standard square root relationship to flow rate, making a simple, removable sensor for installation or retrofit on flowlines of any size.The unique design of the Flo-Bar profile provides a high accuracy, wide rangeability sensor: the standard integral manifold allows simple process isolation and easy installation of a DP measurement cell.
- Flow sensor for liquids, gases or steam
- ± 1% Accuracy with standard square root flow output
- Full electron beam welded construction
- Unique profile sensor with flow averaging
- Integral 3 valve manifold
- Simple direct mounting of DP transmitter if required
- Plain head and remote manifolds available
- An in-line version for small pipes is also available.
T-Bar Valves
A range of fine control valves, suitable for control of high pressure flow lines up to 6,000 psi. The non-rotating, self centreing, anti-galling spindle tip gives positive bubble tight shut-off, plus good flow control.- Bubble tight metal to metal seal for positive shut-off
- Unique bonnet locking cam. No accidental removal of head unit, or loosening due to vibration
- Bi-directional flow, with preferred flow indicator
UKAS and Traceable Calibration
Roxspur Measurement & Control Ltd is an ISO 9001:2008 company, we offer UKAS and traceable calibration under BS/EN ISO17025 accredited procedures. Our certificate generation systems are purposely geared to meet the strict and specific requirement of the Aerospace industry.Calibration
Based at our factory in Sheffield our accredited laboratories are available to provide either on-site or in-house calibration to either UKAS or national standards. We cover Temperature (up to 2,200ºC), Pressure (up to 1,200 bar), Flow (up to 2,500 L/min) and Electrical parameters and provide certification using the latest technology.
Our team of experienced on-site engineers hold accreditation for the on-site calibration of equipment including autoclaves, furnaces, thermocouples and probes, scales and balances, ovens and chambers, indicators and controllers, pressure and electrical. We cover the full spectrum of industry sectors. All calibration standards used meet the requirements of Table 3 of AMS 2750D, whether in the laboratory or on site, ensuring full compliance with the specification. To find out more about our on-site services please click here.
We supply thermocouples calibrated and certified to meet the requirements of Table 1 of AMS 2750D appropriate to customer specified usage.
Aerospace Heat Treatment Specialists
From the supply of a single thermocouple to fully managed service contracts, by working in partnership with our customers we can assist in obtaining and maintaining NADCAP approval. To find out more about our specialist aerospace services please click here.
Certification
Certificates generated are designed to meet the requirements of AMS 2750D with the option of UKAS certificates for added peace of mind.
